Zenders & Ontvangers

PocketWizard MiniTT1 Transmitter An on-camera flash with its own hot shoe while working with remote PocketWizard units. Remotes can be one or more PocketWizard FlexTT5™ Transceivers connected to Canon E-TTL II flashes or any PocketWizard Receiver for triggering flash or remote cameras. The MiniTT1 Transmitter is easy to use; just slide in place and begin to shoot. The new PocketWizard ControlTL™ System interprets the complex E-TTL II data being sent through the camera’s hot shoe and digitally transmits it in a reliable radio signal. Change the flash compensation dial on the camera, and those commands pass seamlessly through the system to your remote flash. Adjust your shutter speed, aperture or ISO and the system corrects for those changes. A ratio command set on the flash or command unit passes through the MiniTT1 to set the remotes. PocketWizard ControlTL radio communication allows you to shoot farther, faster, around corners, through walls even at high noon in bright daylight. Now you can deploy a wireless flash system wherever you want, without infrared limitations, in seconds. Use the MiniTT1 for standard triggering with any PocketWizard Receiver including the FlexTT5, PlusII or MultiMAX. When used this way with a digital camera, you can take advantage of PocketWizard’s HyperSync Technology that allows up to 1/500th of a second camera sync with many camera/strobe set-ups. HyperSync allows you to advance the timing of your flash trigger so that faster than X-sync speeds can be achieved. Need more speed? Push your ControlTL system beyond 1/500th and go into FP/High-Speed sync mode automatically. No buttons to press or settings to change other than your shutter speed will give you flash sync all the way to 1/8000th. A new PocketWizard Utility program is provided to support the MiniTT1 via a USB port. The Utility allows you to configure your channel settings, dial in your HyperSync timing, adjust your sleep-mode timers and update your product to the latest firmware. The PocketWizard MiniTT1 Transmitter is the start of a new era in wireless trigger control! Alleen geschikt voor Nikon!!! Merk Pocket Wizard Type Studioaccessoire Flash Trigger (set) Bereik 1200 feet (800 feet for E-TTL II) Batterijen 3 V Lithium battery, CR2450 (included) or CR2354 Lithium coin cell type Frequentie 433mhz Kanalen 52 Channels over 26 Frequencies Afmetingen 7.1 cm x 4.9 cm x 3.3 cm Gewicht 65 gr. Standaard Garantie 2 jaar

Pocket Wizard Flex TT5 Addition to Canon E-TTL II flash systems. The FlexTT5 takes the existing benefits of Canon wireless systems beyond the boundaries of infrared technology. When paired with the Mini TT1™ Transmitter or another FlexTT5 Transceiver, a whole new world of wireless flash freedom opens up. The FlexTT5 is also the perfect Transceiver for your manual triggering needs and works with all MultiMAX channels and many of the MultiMAX advanced functions. The FlexTT5’s simple design comes to life through its hot-shoe connection with a camera or flash. Mount a flash or command unit on the FlexTT5 to use the same zone controls and ratio commands as you would normally. The system tracks your changes in ISO, shutter speed and aperture and reacts accordingly to make sure exposures stay right on target. Use the flash compensation dial on your camera or flash just as you would normally and the changes pass seamlessly through the system. The FlexTT5 has two channel configuration settings; C1 and C2. Each can be programmed as needed with up to 20 ControlTL channels for TTL photography, or 32 standard channels for manual flash photography. The FlexTT5 Transceiver also has a three-zone selector switch for ease of use with Canon zones and ratios. With PocketWizard HyperSync™ Technology, the FlexTT5 can precisely advance the timing of your flash trigger so that increased flash sync speeds, up to 1/500th of a second is achievable with many strobes. Need more speed? Push your ControlTL system beyond 1/500th and go into FP/High-Speed sync mode automatically. Simply change your shutter speed to get flash sync all the way to 1/8000th. No buttons to press or settings to change! A PocketWizard Utility program is provided to support the FlexTT5 Transceiver via a USB port. The Utility allows you to configure your channel settings, dial in your HyperSync timing, adjust your sleep-mode timers as well as update your product to the latest firmware. The FlexTT5 also has our Auto-Sensing Transceiver Technology that enables it to switch back and forth between Transmitter and Receiver modes as needed for greater flexibility on the job. When a hot-shoe or other trigger is detected, it automatically switches to Transmitter mode. With Auto Relay Mode you can easily trigger a remote camera in sync with remote flash. Put a camera where you can’t be and use remote TTL or non-TTL lighting at the same time. Expand your coverage and increase your creativity. Pocket Wizard Flex TT5 Specificaties.Name PocketWizard FlexTT5 Transceiver Canon Merk Pocket Wizard Type Studioaccessoire Flash Trigger (set) Bereik 1200 feet (800 feet for E-TTL II) Batterijen Two (2) AA (IEC:LR6) Alkaline recommended, other chemistries (NiMH, NiCAD, Lithium) allowed, USB Frequentie 433mhz Kanalen 52 Channels over 26 Frequencies Afmetingen 9.2 cm x 7.3 cm x 3.6 cm Gewicht 153 gr. Standaard Garantie 2 jaar

De Godox X PRO II Transmitter is gemaakt voor TTL systemen. Het stelt u in staat om adequaat en nauwkeurig te flitsen tot 100 meter. Wanneer u hetzelfde object met anderen fotografeert en een set vaste lampen deelt, kunt u de multi-shooting modus proberen. Bij multi-shooting stuurt uw Xpro II de door u ingestelde flitswaarde naar het licht, en de flitser zal werken volgens uw flitswaarde. Terwijl u geniet van het plezier van fotograferen met anderen, past u de flitser aan om uw creatieve ideeën te vervullen.

PowerST4Power Control for Elinchrom RX   The PowerST4 Receiver enables remote power control of Elinchrom RX flashes using PocketWizard ControlTL technology.  With a MiniTT1 Transmitter or FlexTT5 Transceiver on your camera and a PowerST4 plugged into your Elinchrom RX flash, you can now adjust the flash power settings directly from the camera position. Add the AC3 ZoneController and you can control three different zones of lights in 1/3-stop increments with up to a six-stop range.  Utilize PocketWizard’s unique features such as HyperSync and Optimized Rear Curtain Sync for maximum control of your lighting.  Key Benefits: Use PowerTracking and when you change ISO or aperture, the lights automatically adjust their power setting. Add the AC3 ZoneController to control up to three zones of light independently.        o    Use the AC3’s Manual Mode and adjust the             output of your Elinchrom RX flashes from             the camera position in 1/3rd stop             increments.      o    Combine manual and auto modes or toggle             zones on and off and unleash your             creativity. Use HyperSync to increase your maximum x-sync speed and Optimized Rear Curtain Sync to create natural looking movement in your images. Availability:  PowerST4 for Elinchrom Receivers should be arriving at retailers in the US and internationally in September.

Pocket Wizard Zonecontroller For Canon or FlexTT5™ Transceiver and you instantly have three zones of flash control. Whether working in E-TTL II or Manual mode, you now have control over all your flashes directly from the camera’s position. Put your flashes wherever you want, without worrying about having to access them during a shoot. With the AC3 ZoneController, you are in total control of your flash. Three clearly labeled dials allow you to increase or decrease power to three zones of flash in 1/3-stop increments with a range of up to six stops. Three switches allow you to change zones between Manual, Auto (PowerTracking/E-TTL II) or OFF. Best of all, the design is simple with an intuitive interface. Key Benefits: Three independent zones of flash control 6 stops of flash control in 1/3rd stop increments Works in PowerTracking/E-TTL II or Manual mode Turn zones on and off remotely Works with Canon Speedlites. Put your flashes where you want, without worrying about accessing them during a shoot.